Talk to an Expert
Skip to content

Race Ramps 14 Inch Two Piece Supercar Wheel Cribs, Set of 2 | RR-WC-14-SC-2

SKU RR-WC-14-SC-2
Save $17.25
Original Price $362.25
Current Price $345.00

Notify me when back in stock

Katool Mobile and Desktop Trust Badges Katool collection Mobile Trust Badges

One Set of Cribs That Does Two Heights

A crib is a fixed height, so most people end up owning two sets: a tall pair for working underneath, a short pair for anything the car cannot climb. That is two purchases and twice the storage.

The 14" Two Piece Supercar Crib is one purchase. Each crib is two stacked halves. Together they lift 14". Lift the top half off and you have a 7" crib, which means the pair becomes four 7" cribs and the car can sit level on all four corners.

The cradle takes tires up to 16" wide. Each piece carries 1,500 lbs and weighs 6 lbs. Overall height stacked is 15.75" on a 16" square base.

Sold in pairs, for tire diameters 24" to 30". Fixed height alternatives are the 12" supercar crib and the 10" supercar crib. See all wheel cribs.

Race Ramps 14 inch two piece supercar wheel cribs, pair

Benefits of the Two Piece Supercar Crib

Fourteen inches or seven
Stacked it is the tallest crib Race Ramps builds. Split it is a low pair that almost anything can drive onto. You decide at the moment you need it, not at the moment you buy.
A pair becomes four
Two cribs split into four 7 inch cribs, enough to sit the whole car level on all four wheels. That is a job most people need a second set to do.
Sixteen inches of tire width
The supercar cradle, four inches wider than a standard crib. A wide rear tire is carried across its full tread rather than overhanging the edges of the block.
Full rating on each half
Each piece is rated 1,500 lbs on its own, so splitting the set costs you nothing in capacity. Stacked or apart, the number is the same.
6 lbs a piece
Lighter than either fixed crib because the mass is split. Carrying the top half off a 14 inch stack is a one hand job, and the four pieces nest into a corner of the garage.
Safe on a finished floor
Traction coated foam grips epoxy and polished concrete without scratching, and there is no steel to leave a rust ring under a car left standing. Made in the USA with a one year warranty.
Race Ramps RR-WC-14-SC-2 Specifications
Manufacturer Race Ramps
Model RR-WC-14-SC-2
Type Two piece extra wide supercar wheel crib
Sold As Pair, two cribs, four pieces total
Lift Height 14" stacked | 7" split
Dimensions 16" L x 16" W x 15.75" H per crib, stacked
Capacity 1,500 lbs per crib | 3,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 6 lbs per piece, 24 lbs per set
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Two Piece Crib Frequently Asked Questions

How do the halves stay together?

The top piece locates onto the bottom piece and the weight of the car holds the stack. Set them on level ground, seat the top half squarely, and drive up slowly the same way you would onto any crib.

Can a car climb 14 inches?

A crib is a step, not a ramp, so the car has to be lifted onto it or driven up in stages. Many people jack one end, set the stacked cribs, then lower. If the car will not manage it, run the halves split at 7 inches, or call us and we will work out a combination that gets it up safely.

Is it as stable as a one piece crib?

On level ground, yes, and each piece carries the full 1,500 lbs. What a stack does not tolerate is a slope or a piece that is not sitting flat on the one below, so check the seating before the weight goes on.

Do I need the supercar width?

Measure the widest tire on the car. Under 12 inches of section width and a standard crib does the same job for less. Over 12 inches and the tire will overhang a standard cradle, which is what this one is built to avoid.

Can I mix a 14 inch stack with 7 inch pieces?

Only across an axle, never diagonally. Both wheels on the same axle must sit at the same height. Raising one corner higher than the other twists the chassis and loads the suspension in a way it was not designed for.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Overview

One Set of Cribs That Does Two Heights

A crib is a fixed height, so most people end up owning two sets: a tall pair for working underneath, a short pair for anything the car cannot climb. That is two purchases and twice the storage.

The 14" Two Piece Supercar Crib is one purchase. Each crib is two stacked halves. Together they lift 14". Lift the top half off and you have a 7" crib, which means the pair becomes four 7" cribs and the car can sit level on all four corners.

The cradle takes tires up to 16" wide. Each piece carries 1,500 lbs and weighs 6 lbs. Overall height stacked is 15.75" on a 16" square base.

Sold in pairs, for tire diameters 24" to 30". Fixed height alternatives are the 12" supercar crib and the 10" supercar crib. See all wheel cribs.

Race Ramps 14 inch two piece supercar wheel cribs, pair

Benefits of the Two Piece Supercar Crib

Fourteen inches or seven Stacked it is the tallest crib Race Ramps builds. Split it is a low pair that almost anything can drive onto. You decide at the moment you need it, not at the moment you buy. A pair becomes four Two cribs split into four 7 inch cribs, enough to sit the whole car level on all four wheels. That is a job most people need a second set to do. Sixteen inches of tire width The supercar cradle, four inches wider than a standard crib. A wide rear tire is carried across its full tread rather than overhanging the edges of the block. Full rating on each half Each piece is rated 1,500 lbs on its own, so splitting the set costs you nothing in capacity. Stacked or apart, the number is the same. 6 lbs a piece Lighter than either fixed crib because the mass is split. Carrying the top half off a 14 inch stack is a one hand job, and the four pieces nest into a corner of the garage. Safe on a finished floor Traction coated foam grips epoxy and polished concrete without scratching, and there is no steel to leave a rust ring under a car left standing. Made in the USA with a one year warranty.
Race Ramps RR-WC-14-SC-2 Specifications
Manufacturer Race Ramps
Model RR-WC-14-SC-2
Type Two piece extra wide supercar wheel crib
Sold As Pair, two cribs, four pieces total
Lift Height 14" stacked | 7" split
Dimensions 16" L x 16" W x 15.75" H per crib, stacked
Capacity 1,500 lbs per crib | 3,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 6 lbs per piece, 24 lbs per set
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Two Piece Crib Frequently Asked Questions

How do the halves stay together?

The top piece locates onto the bottom piece and the weight of the car holds the stack. Set them on level ground, seat the top half squarely, and drive up slowly the same way you would onto any crib.

Can a car climb 14 inches?

A crib is a step, not a ramp, so the car has to be lifted onto it or driven up in stages. Many people jack one end, set the stacked cribs, then lower. If the car will not manage it, run the halves split at 7 inches, or call us and we will work out a combination that gets it up safely.

Is it as stable as a one piece crib?

On level ground, yes, and each piece carries the full 1,500 lbs. What a stack does not tolerate is a slope or a piece that is not sitting flat on the one below, so check the seating before the weight goes on.

Do I need the supercar width?

Measure the widest tire on the car. Under 12 inches of section width and a standard crib does the same job for less. Over 12 inches and the tire will overhang a standard cradle, which is what this one is built to avoid.

Can I mix a 14 inch stack with 7 inch pieces?

Only across an axle, never diagonally. Both wheels on the same axle must sit at the same height. Raising one corner higher than the other twists the chassis and loads the suspension in a way it was not designed for.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Call (470) 208-2754 Request a Quote Browse Wheel Cribs
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews
NO SALES TAX

Orders outside GA, IL, OH are 100% sales tax-free

Give us a call

Our phone team is available 8 AM - 8 PM ET, every day at 470-208-2754

Lifetime Support

Enjoy peace of mind with our support for life. Get in touch!

700+ Reviews

Highly rated and customer-approved. View all!

Overview

One Set of Cribs That Does Two Heights

A crib is a fixed height, so most people end up owning two sets: a tall pair for working underneath, a short pair for anything the car cannot climb. That is two purchases and twice the storage.

The 14" Two Piece Supercar Crib is one purchase. Each crib is two stacked halves. Together they lift 14". Lift the top half off and you have a 7" crib, which means the pair becomes four 7" cribs and the car can sit level on all four corners.

The cradle takes tires up to 16" wide. Each piece carries 1,500 lbs and weighs 6 lbs. Overall height stacked is 15.75" on a 16" square base.

Sold in pairs, for tire diameters 24" to 30". Fixed height alternatives are the 12" supercar crib and the 10" supercar crib. See all wheel cribs.

Race Ramps 14 inch two piece supercar wheel cribs, pair

Benefits of the Two Piece Supercar Crib

Fourteen inches or seven Stacked it is the tallest crib Race Ramps builds. Split it is a low pair that almost anything can drive onto. You decide at the moment you need it, not at the moment you buy. A pair becomes four Two cribs split into four 7 inch cribs, enough to sit the whole car level on all four wheels. That is a job most people need a second set to do. Sixteen inches of tire width The supercar cradle, four inches wider than a standard crib. A wide rear tire is carried across its full tread rather than overhanging the edges of the block. Full rating on each half Each piece is rated 1,500 lbs on its own, so splitting the set costs you nothing in capacity. Stacked or apart, the number is the same. 6 lbs a piece Lighter than either fixed crib because the mass is split. Carrying the top half off a 14 inch stack is a one hand job, and the four pieces nest into a corner of the garage. Safe on a finished floor Traction coated foam grips epoxy and polished concrete without scratching, and there is no steel to leave a rust ring under a car left standing. Made in the USA with a one year warranty.
Race Ramps RR-WC-14-SC-2 Specifications
Manufacturer Race Ramps
Model RR-WC-14-SC-2
Type Two piece extra wide supercar wheel crib
Sold As Pair, two cribs, four pieces total
Lift Height 14" stacked | 7" split
Dimensions 16" L x 16" W x 15.75" H per crib, stacked
Capacity 1,500 lbs per crib | 3,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 6 lbs per piece, 24 lbs per set
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Two Piece Crib Frequently Asked Questions

How do the halves stay together?

The top piece locates onto the bottom piece and the weight of the car holds the stack. Set them on level ground, seat the top half squarely, and drive up slowly the same way you would onto any crib.

Can a car climb 14 inches?

A crib is a step, not a ramp, so the car has to be lifted onto it or driven up in stages. Many people jack one end, set the stacked cribs, then lower. If the car will not manage it, run the halves split at 7 inches, or call us and we will work out a combination that gets it up safely.

Is it as stable as a one piece crib?

On level ground, yes, and each piece carries the full 1,500 lbs. What a stack does not tolerate is a slope or a piece that is not sitting flat on the one below, so check the seating before the weight goes on.

Do I need the supercar width?

Measure the widest tire on the car. Under 12 inches of section width and a standard crib does the same job for less. Over 12 inches and the tire will overhang a standard cradle, which is what this one is built to avoid.

Can I mix a 14 inch stack with 7 inch pieces?

Only across an axle, never diagonally. Both wheels on the same axle must sit at the same height. Raising one corner higher than the other twists the chassis and loads the suspension in a way it was not designed for.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Call (470) 208-2754 Request a Quote Browse Wheel Cribs
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews