Talk to an Expert
Skip to content

Race Ramps 10 Inch Supercar Wheel Cribs, Set of 2 | RR-WC-10-SC

SKU RR-WC-10-SC
Save $11.40
Original Price $239.40
Current Price $228.00

Notify me when back in stock

Katool Mobile and Desktop Trust Badges Katool collection Mobile Trust Badges

Wide Tire Support at a Height a Low Car Can Climb

Two inches does not sound like much until the car will not make the step. The 12" Supercar Crib is the one most people reach for, and on a car with a low front lip it is the one that stops them at the bottom.

The 10" Supercar Crib is the same 16" wide cradle on a shorter block. Tires up to 16" wide sit fully carried across the tread instead of overhanging the sides, and the climb is two inches less.

Lift is 10" to the cradle, overall height 11.375". Each crib carries 1,500 lbs and weighs 8.5 lbs. Solid foam with a traction coating that holds on epoxy and polished concrete without marking it.

Sold in pairs, for tire diameters 24" to 30". Tires 12" or narrower fit the cheaper standard 10" cribs. See all wheel cribs.

Race Ramps 10 inch supercar wheel cribs, pair

Benefits of the 10 Inch Supercar Crib

Sixteen inches of tire width
Four inches more than a standard crib. A wide rear tire sits inside the cradle instead of hanging over both edges of it, which is the entire reason the supercar version exists.
Two inches easier to climb
The shortest crib in the supercar range. If the 12 inch version is more step than the car will take without scraping, this is the one that gets it up.
No jack, no jacking points
You drive up onto it. On a car with a carbon undertray and pinch welds you would rather not test, never going underneath with a jack is worth the price on its own.
Load through the tread
A tire wider than its support concentrates weight on the outer corners of the block. Matching crib width to tire width puts the load through the full contact patch and straight down through the foam.
8.5 lbs each
A pair goes under one arm. There is no steel to rust and nothing to pinch a finger, and the set stores upright in the space a toolbox would take.
Made for a finished floor
Traction coated foam grips epoxy and polished concrete without scratching, and leaves no rust ring if the car sits on them through a season. Made in the USA with a one year warranty.
Race Ramps RR-WC-10-SC Specifications
Manufacturer Race Ramps
Model RR-WC-10-SC
Type Extra wide supercar wheel crib
Sold As Pair, two cribs
Lift Height 10" to the cradle
Dimensions 15" L x 16" W x 11.375" H per crib
Capacity 1,500 lbs per crib | 3,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 8.5 lbs per crib, 17 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Supercar Crib Frequently Asked Questions

Should I buy the 10 inch or the 12 inch supercar crib?

Both take the same 16 inch tire width, so the choice is only about height. Take the 12 inch version if you want maximum working clearance and the car can climb it. Take this one if the car is low enough that the extra two inches is a problem.

Do I actually need the supercar version?

Measure the widest tire on the car. At 12 inches of section width or under, the standard 10 inch cribs give the same lift and capacity for less. Over 12 inches, you want these.

What if only the rear tires are wide?

Common on a staggered setup. Run the supercar pair at the rear and standard cribs at the front, matched for height. Mixing is fine as long as every tire is fully carried by the crib it is sitting on.

Why is the block 11.375 inches tall if the lift is 10?

The cradle is dished so the tire settles into it. Ten inches is the height of the cradle floor where the tire rests. The 11.375 figure is the outside height of the block including the raised sides that locate the tire.

Can I leave the car on them long term?

Yes. Foam does not sag, rust, or leak down the way a jack stand and a hydraulic jack can, which is why cribs are the usual choice for a car going into winter storage. The contoured cradle also spreads the load rather than resting the tire on one flat spot.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Overview

Wide Tire Support at a Height a Low Car Can Climb

Two inches does not sound like much until the car will not make the step. The 12" Supercar Crib is the one most people reach for, and on a car with a low front lip it is the one that stops them at the bottom.

The 10" Supercar Crib is the same 16" wide cradle on a shorter block. Tires up to 16" wide sit fully carried across the tread instead of overhanging the sides, and the climb is two inches less.

Lift is 10" to the cradle, overall height 11.375". Each crib carries 1,500 lbs and weighs 8.5 lbs. Solid foam with a traction coating that holds on epoxy and polished concrete without marking it.

Sold in pairs, for tire diameters 24" to 30". Tires 12" or narrower fit the cheaper standard 10" cribs. See all wheel cribs.

Race Ramps 10 inch supercar wheel cribs, pair

Benefits of the 10 Inch Supercar Crib

Sixteen inches of tire width Four inches more than a standard crib. A wide rear tire sits inside the cradle instead of hanging over both edges of it, which is the entire reason the supercar version exists. Two inches easier to climb The shortest crib in the supercar range. If the 12 inch version is more step than the car will take without scraping, this is the one that gets it up. No jack, no jacking points You drive up onto it. On a car with a carbon undertray and pinch welds you would rather not test, never going underneath with a jack is worth the price on its own. Load through the tread A tire wider than its support concentrates weight on the outer corners of the block. Matching crib width to tire width puts the load through the full contact patch and straight down through the foam. 8.5 lbs each A pair goes under one arm. There is no steel to rust and nothing to pinch a finger, and the set stores upright in the space a toolbox would take. Made for a finished floor Traction coated foam grips epoxy and polished concrete without scratching, and leaves no rust ring if the car sits on them through a season. Made in the USA with a one year warranty.
Race Ramps RR-WC-10-SC Specifications
Manufacturer Race Ramps
Model RR-WC-10-SC
Type Extra wide supercar wheel crib
Sold As Pair, two cribs
Lift Height 10" to the cradle
Dimensions 15" L x 16" W x 11.375" H per crib
Capacity 1,500 lbs per crib | 3,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 8.5 lbs per crib, 17 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Supercar Crib Frequently Asked Questions

Should I buy the 10 inch or the 12 inch supercar crib?

Both take the same 16 inch tire width, so the choice is only about height. Take the 12 inch version if you want maximum working clearance and the car can climb it. Take this one if the car is low enough that the extra two inches is a problem.

Do I actually need the supercar version?

Measure the widest tire on the car. At 12 inches of section width or under, the standard 10 inch cribs give the same lift and capacity for less. Over 12 inches, you want these.

What if only the rear tires are wide?

Common on a staggered setup. Run the supercar pair at the rear and standard cribs at the front, matched for height. Mixing is fine as long as every tire is fully carried by the crib it is sitting on.

Why is the block 11.375 inches tall if the lift is 10?

The cradle is dished so the tire settles into it. Ten inches is the height of the cradle floor where the tire rests. The 11.375 figure is the outside height of the block including the raised sides that locate the tire.

Can I leave the car on them long term?

Yes. Foam does not sag, rust, or leak down the way a jack stand and a hydraulic jack can, which is why cribs are the usual choice for a car going into winter storage. The contoured cradle also spreads the load rather than resting the tire on one flat spot.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Call (470) 208-2754 Request a Quote Browse Wheel Cribs
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews
NO SALES TAX

Orders outside GA, IL, OH are 100% sales tax-free

Give us a call

Our phone team is available 8 AM - 8 PM ET, every day at 470-208-2754

Lifetime Support

Enjoy peace of mind with our support for life. Get in touch!

700+ Reviews

Highly rated and customer-approved. View all!

Overview

Wide Tire Support at a Height a Low Car Can Climb

Two inches does not sound like much until the car will not make the step. The 12" Supercar Crib is the one most people reach for, and on a car with a low front lip it is the one that stops them at the bottom.

The 10" Supercar Crib is the same 16" wide cradle on a shorter block. Tires up to 16" wide sit fully carried across the tread instead of overhanging the sides, and the climb is two inches less.

Lift is 10" to the cradle, overall height 11.375". Each crib carries 1,500 lbs and weighs 8.5 lbs. Solid foam with a traction coating that holds on epoxy and polished concrete without marking it.

Sold in pairs, for tire diameters 24" to 30". Tires 12" or narrower fit the cheaper standard 10" cribs. See all wheel cribs.

Race Ramps 10 inch supercar wheel cribs, pair

Benefits of the 10 Inch Supercar Crib

Sixteen inches of tire width Four inches more than a standard crib. A wide rear tire sits inside the cradle instead of hanging over both edges of it, which is the entire reason the supercar version exists. Two inches easier to climb The shortest crib in the supercar range. If the 12 inch version is more step than the car will take without scraping, this is the one that gets it up. No jack, no jacking points You drive up onto it. On a car with a carbon undertray and pinch welds you would rather not test, never going underneath with a jack is worth the price on its own. Load through the tread A tire wider than its support concentrates weight on the outer corners of the block. Matching crib width to tire width puts the load through the full contact patch and straight down through the foam. 8.5 lbs each A pair goes under one arm. There is no steel to rust and nothing to pinch a finger, and the set stores upright in the space a toolbox would take. Made for a finished floor Traction coated foam grips epoxy and polished concrete without scratching, and leaves no rust ring if the car sits on them through a season. Made in the USA with a one year warranty.
Race Ramps RR-WC-10-SC Specifications
Manufacturer Race Ramps
Model RR-WC-10-SC
Type Extra wide supercar wheel crib
Sold As Pair, two cribs
Lift Height 10" to the cradle
Dimensions 15" L x 16" W x 11.375" H per crib
Capacity 1,500 lbs per crib | 3,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 8.5 lbs per crib, 17 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Supercar Crib Frequently Asked Questions

Should I buy the 10 inch or the 12 inch supercar crib?

Both take the same 16 inch tire width, so the choice is only about height. Take the 12 inch version if you want maximum working clearance and the car can climb it. Take this one if the car is low enough that the extra two inches is a problem.

Do I actually need the supercar version?

Measure the widest tire on the car. At 12 inches of section width or under, the standard 10 inch cribs give the same lift and capacity for less. Over 12 inches, you want these.

What if only the rear tires are wide?

Common on a staggered setup. Run the supercar pair at the rear and standard cribs at the front, matched for height. Mixing is fine as long as every tire is fully carried by the crib it is sitting on.

Why is the block 11.375 inches tall if the lift is 10?

The cradle is dished so the tire settles into it. Ten inches is the height of the cradle floor where the tire rests. The 11.375 figure is the outside height of the block including the raised sides that locate the tire.

Can I leave the car on them long term?

Yes. Foam does not sag, rust, or leak down the way a jack stand and a hydraulic jack can, which is why cribs are the usual choice for a car going into winter storage. The contoured cradle also spreads the load rather than resting the tire on one flat spot.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Call (470) 208-2754 Request a Quote Browse Wheel Cribs
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews