Talk to an Expert
Skip to content

Race Ramps 12 Inch Supercar Wheel Cribs, Set of 2 | RR-WC-12-SC

SKU RR-WC-12-SC
Save $12.25
Original Price $257.25
Current Price $245.00

Notify me when back in stock

Katool Mobile and Desktop Trust Badges Katool collection Mobile Trust Badges

For Tires the Standard Cribs Cannot Take: Race Ramps 12" Supercar Cribs

A 335 section rear tire does not fit a standard wheel crib. It overhangs the cradle on both sides, which puts the load on the edges of the block instead of across the tread, and it looks wrong sitting there even before you think about whether it is safe.

The Supercar Cribs are the wide answer. The cradle takes tires up to 16" wide, four inches more than the standard 12" crib, on a body 16" across. The tire sits fully supported instead of perched.

Lift is 12" to the cradle with an overall height of 13.25". Each crib carries 1,500 lbs, 6,000 lbs across the pair, and weighs 9 lbs. Solid foam with a traction coating that grips a finished floor without marking it.

Sold in pairs, for tire diameters 24" to 30". If your tires are 12" or narrower, the standard 12" cribs cost less and do the same job. See all wheel cribs.

Race Ramps 12 inch supercar wheel cribs, pair

Benefits of the Supercar Cribs

Sixteen inches of tire width
Four inches more than the standard crib. That is the difference between a wide rear tire being fully carried by the cradle and hanging over both edges of it, which is the only reason this version exists.
Load across the tread, not the edges
A tire wider than its support concentrates weight on the outer corners of the block. Matching the crib to the tire puts the load through the full contact patch and down through the foam as intended.
Twelve inches of clearance
Same working height as the standard 12 inch crib, so you lose nothing by going wide. Enough room for exhaust work, underbody inspection, or displaying the car properly.
Still no jack required
You drive up. On a car worth what a supercar is worth, not hunting for a jacking point under a carbon undertray is worth something on its own.
9 lbs each
The heaviest crib in the range and still trivial to carry. A pair goes under one arm and stores in the space a toolbox would take.
Safe on the floor it will live on
Traction coated foam grips epoxy and polished concrete without scratching, and no steel means no rust ring if the car sits for a season. Made in the USA with a one year warranty.
Race Ramps RR-WC-12-SC Specifications
Manufacturer Race Ramps
Model RR-WC-12-SC
Type Extra wide supercar wheel crib
Sold As Pair, two cribs
Lift Height 12" to the cradle
Dimensions 15.5" L x 16" W x 13.25" H per crib
Capacity 1,500 lbs per crib | 6,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 9 lbs per crib, 18 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Supercar Crib Frequently Asked Questions

Do I actually need the supercar version?

Only if your tires are wider than 12 inches of section width. Measure the widest tire on the car. If it is 12 inches or under, the standard 12 inch cribs give the same lift and capacity for less money. If it is over, you want these.

What if only the rear tires are wide?

Common on a staggered setup. Buy the supercar pair for the rear and standard cribs for the front, or buy two supercar pairs and use them all round. Mixing is fine as long as each tire is properly supported by the crib it is on.

Is the capacity higher too?

No, it is the same 1,500 lbs per crib as the rest of the range, which is plenty for any car. The upgrade is width, not load rating.

Why is it 13.25 inches tall if the lift is 12?

The cradle is dished, so the tire sits down into it. Twelve inches is the height of the cradle floor where the tire rests, and 13.25 is the outside height of the block including the raised sides that locate the tire.

Can a supercar climb 12 inches?

This is the real question, because the cars that need 16 inch cribs are often the lowest cars on the road. A crib is a step, not a ramp. If your car will not make the climb, use ramps to raise it first, or call us and we will work out a combination that gets it up safely.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Overview

For Tires the Standard Cribs Cannot Take: Race Ramps 12" Supercar Cribs

A 335 section rear tire does not fit a standard wheel crib. It overhangs the cradle on both sides, which puts the load on the edges of the block instead of across the tread, and it looks wrong sitting there even before you think about whether it is safe.

The Supercar Cribs are the wide answer. The cradle takes tires up to 16" wide, four inches more than the standard 12" crib, on a body 16" across. The tire sits fully supported instead of perched.

Lift is 12" to the cradle with an overall height of 13.25". Each crib carries 1,500 lbs, 6,000 lbs across the pair, and weighs 9 lbs. Solid foam with a traction coating that grips a finished floor without marking it.

Sold in pairs, for tire diameters 24" to 30". If your tires are 12" or narrower, the standard 12" cribs cost less and do the same job. See all wheel cribs.

Race Ramps 12 inch supercar wheel cribs, pair

Benefits of the Supercar Cribs

Sixteen inches of tire width Four inches more than the standard crib. That is the difference between a wide rear tire being fully carried by the cradle and hanging over both edges of it, which is the only reason this version exists. Load across the tread, not the edges A tire wider than its support concentrates weight on the outer corners of the block. Matching the crib to the tire puts the load through the full contact patch and down through the foam as intended. Twelve inches of clearance Same working height as the standard 12 inch crib, so you lose nothing by going wide. Enough room for exhaust work, underbody inspection, or displaying the car properly. Still no jack required You drive up. On a car worth what a supercar is worth, not hunting for a jacking point under a carbon undertray is worth something on its own. 9 lbs each The heaviest crib in the range and still trivial to carry. A pair goes under one arm and stores in the space a toolbox would take. Safe on the floor it will live on Traction coated foam grips epoxy and polished concrete without scratching, and no steel means no rust ring if the car sits for a season. Made in the USA with a one year warranty.
Race Ramps RR-WC-12-SC Specifications
Manufacturer Race Ramps
Model RR-WC-12-SC
Type Extra wide supercar wheel crib
Sold As Pair, two cribs
Lift Height 12" to the cradle
Dimensions 15.5" L x 16" W x 13.25" H per crib
Capacity 1,500 lbs per crib | 6,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 9 lbs per crib, 18 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Supercar Crib Frequently Asked Questions

Do I actually need the supercar version?

Only if your tires are wider than 12 inches of section width. Measure the widest tire on the car. If it is 12 inches or under, the standard 12 inch cribs give the same lift and capacity for less money. If it is over, you want these.

What if only the rear tires are wide?

Common on a staggered setup. Buy the supercar pair for the rear and standard cribs for the front, or buy two supercar pairs and use them all round. Mixing is fine as long as each tire is properly supported by the crib it is on.

Is the capacity higher too?

No, it is the same 1,500 lbs per crib as the rest of the range, which is plenty for any car. The upgrade is width, not load rating.

Why is it 13.25 inches tall if the lift is 12?

The cradle is dished, so the tire sits down into it. Twelve inches is the height of the cradle floor where the tire rests, and 13.25 is the outside height of the block including the raised sides that locate the tire.

Can a supercar climb 12 inches?

This is the real question, because the cars that need 16 inch cribs are often the lowest cars on the road. A crib is a step, not a ramp. If your car will not make the climb, use ramps to raise it first, or call us and we will work out a combination that gets it up safely.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Call (470) 208-2754 Request a Quote Browse Wheel Cribs
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews
NO SALES TAX

Orders outside GA, IL, OH are 100% sales tax-free

Give us a call

Our phone team is available 8 AM - 8 PM ET, every day at 470-208-2754

Lifetime Support

Enjoy peace of mind with our support for life. Get in touch!

700+ Reviews

Highly rated and customer-approved. View all!

Overview

For Tires the Standard Cribs Cannot Take: Race Ramps 12" Supercar Cribs

A 335 section rear tire does not fit a standard wheel crib. It overhangs the cradle on both sides, which puts the load on the edges of the block instead of across the tread, and it looks wrong sitting there even before you think about whether it is safe.

The Supercar Cribs are the wide answer. The cradle takes tires up to 16" wide, four inches more than the standard 12" crib, on a body 16" across. The tire sits fully supported instead of perched.

Lift is 12" to the cradle with an overall height of 13.25". Each crib carries 1,500 lbs, 6,000 lbs across the pair, and weighs 9 lbs. Solid foam with a traction coating that grips a finished floor without marking it.

Sold in pairs, for tire diameters 24" to 30". If your tires are 12" or narrower, the standard 12" cribs cost less and do the same job. See all wheel cribs.

Race Ramps 12 inch supercar wheel cribs, pair

Benefits of the Supercar Cribs

Sixteen inches of tire width Four inches more than the standard crib. That is the difference between a wide rear tire being fully carried by the cradle and hanging over both edges of it, which is the only reason this version exists. Load across the tread, not the edges A tire wider than its support concentrates weight on the outer corners of the block. Matching the crib to the tire puts the load through the full contact patch and down through the foam as intended. Twelve inches of clearance Same working height as the standard 12 inch crib, so you lose nothing by going wide. Enough room for exhaust work, underbody inspection, or displaying the car properly. Still no jack required You drive up. On a car worth what a supercar is worth, not hunting for a jacking point under a carbon undertray is worth something on its own. 9 lbs each The heaviest crib in the range and still trivial to carry. A pair goes under one arm and stores in the space a toolbox would take. Safe on the floor it will live on Traction coated foam grips epoxy and polished concrete without scratching, and no steel means no rust ring if the car sits for a season. Made in the USA with a one year warranty.
Race Ramps RR-WC-12-SC Specifications
Manufacturer Race Ramps
Model RR-WC-12-SC
Type Extra wide supercar wheel crib
Sold As Pair, two cribs
Lift Height 12" to the cradle
Dimensions 15.5" L x 16" W x 13.25" H per crib
Capacity 1,500 lbs per crib | 6,000 lbs per pair
Maximum Tire Width 16"
Tire Diameter Range 24" to 30" overall
Weight 9 lbs per crib, 18 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

Supercar Crib Frequently Asked Questions

Do I actually need the supercar version?

Only if your tires are wider than 12 inches of section width. Measure the widest tire on the car. If it is 12 inches or under, the standard 12 inch cribs give the same lift and capacity for less money. If it is over, you want these.

What if only the rear tires are wide?

Common on a staggered setup. Buy the supercar pair for the rear and standard cribs for the front, or buy two supercar pairs and use them all round. Mixing is fine as long as each tire is properly supported by the crib it is on.

Is the capacity higher too?

No, it is the same 1,500 lbs per crib as the rest of the range, which is plenty for any car. The upgrade is width, not load rating.

Why is it 13.25 inches tall if the lift is 12?

The cradle is dished, so the tire sits down into it. Twelve inches is the height of the cradle floor where the tire rests, and 13.25 is the outside height of the block including the raised sides that locate the tire.

Can a supercar climb 12 inches?

This is the real question, because the cars that need 16 inch cribs are often the lowest cars on the road. A crib is a step, not a ramp. If your car will not make the climb, use ramps to raise it first, or call us and we will work out a combination that gets it up safely.

Questions about fitment? Talk to a Pitstop Pro specialist or explore more options.

Call (470) 208-2754 Request a Quote Browse Wheel Cribs
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews