Talk to an Expert
Skip to content

Race Ramps XTenders for 56 and 67 Inch Car Ramps, 6.6 Degree Approach

SKU RR-EX-12
Save $9.00
Original Price $189.00
Current Price $180.00

Notify me when back in stock

Katool Mobile and Desktop Trust Badges Katool collection Mobile Trust Badges

Turn the Ramps You Own Into 6.6 Degree Ramps

These are add on inclines, not ramps. They fit in front of 56" or 67" Race Ramps and do not include the ramps themselves. Pick the version that matches the ramps you already own.

You bought the ramps, the car got lower, and now the nose touches on the way up. Replacing a good set of ramps to buy back a few degrees is an expensive answer to that problem.

An XTender is a long, shallow wedge that sits in front of the ramp so the tire starts climbing four feet earlier. The combined approach drops to 6.6 degrees, gentler than every ramp in the Race Ramps line.

The 12" wide version is 45" long and fits 56" ramps. The 14" wide version is 48" long and fits 67" ramps, including the Race Ramps XT. Both weigh 10 lbs each.

Sold in pairs. If you have not bought ramps yet, the 72" two stage ramps open at 6.8 degrees on their own. See all low profile car ramps.

Race Ramps XTenders shown in front of a car ramp

Benefits of the XTenders

The gentlest approach Race Ramps offer
6.6 degrees is shallower than the 72 inch two stage ramp at 6.8 and well under the XT at 10.8. If a car will not climb anything, this is the combination to try.
Keeps the ramps you already paid for
Far cheaper than replacing a good set of 56 or 67 inch ramps because the car dropped an inch. You are buying the missing few degrees, not starting over.
No lift height sacrificed
The usual way to get a shallower climb is to lift less. This keeps the full height of your existing ramps and buys the angle back with length instead.
Only when you need it
Leave them off for the daily and put them down for the low car. Ten pounds each means moving them in and out of the way is not a job you avoid.
Matched widths, no overhang
12 inches for the 56 inch ramps and 14 inches for the 67 inch ramps, so the tire tracks straight from one onto the other with no step or edge at the joint.
Grips instead of sliding away
The traction coating matters more on an extender than anywhere, because the tire meets it first and pushes forward. Foam holds on epoxy and sealed concrete without marking. Made in the USA with a one year warranty.
Race Ramps XTenders Specifications
Model RR-EX-12 RR-EX-14
Fits 56" Race Ramps 67" Race Ramps
Length 45" 48"
Width 12" 14"
Height at the Joint 2.67" 2.67"
Combined Approach Angle 6.6 degrees 6.6 degrees
Weight 10 lbs each, 20 lbs per pair 10 lbs each, 20 lbs per pair
Sold As Pair, two XTenders. Ramps not included
Manufacturer Race Ramps
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

XTender Frequently Asked Questions

Do I get ramps with this?

No. This is the pair of extenders only. They are useless on their own and need 56 or 67 inch Race Ramps in front of them. If you do not own a set yet, call us on (470) 208-2754 and we will quote the pair together.

Which version do I need?

Match it to your ramps. The 12 inch wide XTender is for 56 inch Race Ramps. The 14 inch wide is for 67 inch Race Ramps, which includes the XT and the XT two piece. They are not interchangeable, so check the model number on your ramps before ordering.

Will they fit any other Race Ramps?

Race Ramps specify 56 and 67 inch ramps only. Portable Pit Stop and 16 inch Restyler ramps take a different extender with a fold. Tell us which ramps you have and we will confirm which part you need.

How much extra floor space do I need?

About four extra feet in front of each ramp, so roughly nine feet of total run once the ramp itself is counted. In a standard garage that usually means pulling the car well back before you start.

Does the joint between them cause a bump?

The XTender is cut to meet the ramp face at matching height and width, so the tire rolls through the transition rather than stepping up. Set them square and pushed together, and drive up slowly the first time to check the alignment.

Not sure which ramps you have? Talk to a Pitstop Pro specialist.

Overview

Turn the Ramps You Own Into 6.6 Degree Ramps

These are add on inclines, not ramps. They fit in front of 56" or 67" Race Ramps and do not include the ramps themselves. Pick the version that matches the ramps you already own.

You bought the ramps, the car got lower, and now the nose touches on the way up. Replacing a good set of ramps to buy back a few degrees is an expensive answer to that problem.

An XTender is a long, shallow wedge that sits in front of the ramp so the tire starts climbing four feet earlier. The combined approach drops to 6.6 degrees, gentler than every ramp in the Race Ramps line.

The 12" wide version is 45" long and fits 56" ramps. The 14" wide version is 48" long and fits 67" ramps, including the Race Ramps XT. Both weigh 10 lbs each.

Sold in pairs. If you have not bought ramps yet, the 72" two stage ramps open at 6.8 degrees on their own. See all low profile car ramps.

Race Ramps XTenders shown in front of a car ramp

Benefits of the XTenders

The gentlest approach Race Ramps offer 6.6 degrees is shallower than the 72 inch two stage ramp at 6.8 and well under the XT at 10.8. If a car will not climb anything, this is the combination to try. Keeps the ramps you already paid for Far cheaper than replacing a good set of 56 or 67 inch ramps because the car dropped an inch. You are buying the missing few degrees, not starting over. No lift height sacrificed The usual way to get a shallower climb is to lift less. This keeps the full height of your existing ramps and buys the angle back with length instead. Only when you need it Leave them off for the daily and put them down for the low car. Ten pounds each means moving them in and out of the way is not a job you avoid. Matched widths, no overhang 12 inches for the 56 inch ramps and 14 inches for the 67 inch ramps, so the tire tracks straight from one onto the other with no step or edge at the joint. Grips instead of sliding away The traction coating matters more on an extender than anywhere, because the tire meets it first and pushes forward. Foam holds on epoxy and sealed concrete without marking. Made in the USA with a one year warranty.
Race Ramps XTenders Specifications
Model RR-EX-12 RR-EX-14
Fits 56" Race Ramps 67" Race Ramps
Length 45" 48"
Width 12" 14"
Height at the Joint 2.67" 2.67"
Combined Approach Angle 6.6 degrees 6.6 degrees
Weight 10 lbs each, 20 lbs per pair 10 lbs each, 20 lbs per pair
Sold As Pair, two XTenders. Ramps not included
Manufacturer Race Ramps
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

XTender Frequently Asked Questions

Do I get ramps with this?

No. This is the pair of extenders only. They are useless on their own and need 56 or 67 inch Race Ramps in front of them. If you do not own a set yet, call us on (470) 208-2754 and we will quote the pair together.

Which version do I need?

Match it to your ramps. The 12 inch wide XTender is for 56 inch Race Ramps. The 14 inch wide is for 67 inch Race Ramps, which includes the XT and the XT two piece. They are not interchangeable, so check the model number on your ramps before ordering.

Will they fit any other Race Ramps?

Race Ramps specify 56 and 67 inch ramps only. Portable Pit Stop and 16 inch Restyler ramps take a different extender with a fold. Tell us which ramps you have and we will confirm which part you need.

How much extra floor space do I need?

About four extra feet in front of each ramp, so roughly nine feet of total run once the ramp itself is counted. In a standard garage that usually means pulling the car well back before you start.

Does the joint between them cause a bump?

The XTender is cut to meet the ramp face at matching height and width, so the tire rolls through the transition rather than stepping up. Set them square and pushed together, and drive up slowly the first time to check the alignment.

Not sure which ramps you have? Talk to a Pitstop Pro specialist.

Call (470) 208-2754 Request a Quote Browse Car Ramps
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews
NO SALES TAX

Orders outside GA, IL, OH are 100% sales tax-free

Give us a call

Our phone team is available 8 AM - 8 PM ET, every day at 470-208-2754

Lifetime Support

Enjoy peace of mind with our support for life. Get in touch!

700+ Reviews

Highly rated and customer-approved. View all!

Overview

Turn the Ramps You Own Into 6.6 Degree Ramps

These are add on inclines, not ramps. They fit in front of 56" or 67" Race Ramps and do not include the ramps themselves. Pick the version that matches the ramps you already own.

You bought the ramps, the car got lower, and now the nose touches on the way up. Replacing a good set of ramps to buy back a few degrees is an expensive answer to that problem.

An XTender is a long, shallow wedge that sits in front of the ramp so the tire starts climbing four feet earlier. The combined approach drops to 6.6 degrees, gentler than every ramp in the Race Ramps line.

The 12" wide version is 45" long and fits 56" ramps. The 14" wide version is 48" long and fits 67" ramps, including the Race Ramps XT. Both weigh 10 lbs each.

Sold in pairs. If you have not bought ramps yet, the 72" two stage ramps open at 6.8 degrees on their own. See all low profile car ramps.

Race Ramps XTenders shown in front of a car ramp

Benefits of the XTenders

The gentlest approach Race Ramps offer 6.6 degrees is shallower than the 72 inch two stage ramp at 6.8 and well under the XT at 10.8. If a car will not climb anything, this is the combination to try. Keeps the ramps you already paid for Far cheaper than replacing a good set of 56 or 67 inch ramps because the car dropped an inch. You are buying the missing few degrees, not starting over. No lift height sacrificed The usual way to get a shallower climb is to lift less. This keeps the full height of your existing ramps and buys the angle back with length instead. Only when you need it Leave them off for the daily and put them down for the low car. Ten pounds each means moving them in and out of the way is not a job you avoid. Matched widths, no overhang 12 inches for the 56 inch ramps and 14 inches for the 67 inch ramps, so the tire tracks straight from one onto the other with no step or edge at the joint. Grips instead of sliding away The traction coating matters more on an extender than anywhere, because the tire meets it first and pushes forward. Foam holds on epoxy and sealed concrete without marking. Made in the USA with a one year warranty.
Race Ramps XTenders Specifications
Model RR-EX-12 RR-EX-14
Fits 56" Race Ramps 67" Race Ramps
Length 45" 48"
Width 12" 14"
Height at the Joint 2.67" 2.67"
Combined Approach Angle 6.6 degrees 6.6 degrees
Weight 10 lbs each, 20 lbs per pair 10 lbs each, 20 lbs per pair
Sold As Pair, two XTenders. Ramps not included
Manufacturer Race Ramps
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

XTender Frequently Asked Questions

Do I get ramps with this?

No. This is the pair of extenders only. They are useless on their own and need 56 or 67 inch Race Ramps in front of them. If you do not own a set yet, call us on (470) 208-2754 and we will quote the pair together.

Which version do I need?

Match it to your ramps. The 12 inch wide XTender is for 56 inch Race Ramps. The 14 inch wide is for 67 inch Race Ramps, which includes the XT and the XT two piece. They are not interchangeable, so check the model number on your ramps before ordering.

Will they fit any other Race Ramps?

Race Ramps specify 56 and 67 inch ramps only. Portable Pit Stop and 16 inch Restyler ramps take a different extender with a fold. Tell us which ramps you have and we will confirm which part you need.

How much extra floor space do I need?

About four extra feet in front of each ramp, so roughly nine feet of total run once the ramp itself is counted. In a standard garage that usually means pulling the car well back before you start.

Does the joint between them cause a bump?

The XTender is cut to meet the ramp face at matching height and width, so the tire rolls through the transition rather than stepping up. Set them square and pushed together, and drive up slowly the first time to check the alignment.

Not sure which ramps you have? Talk to a Pitstop Pro specialist.

Call (470) 208-2754 Request a Quote Browse Car Ramps
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews