Skip to content

Race Ramps Folding XTenders for Portable Pit Stop and 16 Inch Restyler Ramps | RR-EX-PPS

SKU RR-EX-PPS
Sold out
Original Price $666.75
Current Price $634.00

Notify me when back in stock

Katool Mobile and Desktop Trust Badges Katool collection Mobile Trust Badges

Six Feet of Extra Run, and It Folds in Half

These are add on inclines, not ramps. They fit Portable Pit Stop Ramps and 16 inch Restyler Ramps, Magna and Classic. Running the 20 inch Restyler? That system takes RR-EX-20 instead, which is a call to order. Ramps are not included either way.

Portable Pit Stop and Restyler ramps lift a long way, and lifting a long way over a fixed length means an angle that a splitter finds first. The car stops, or it does not, and you find out the hard way.

These XTenders put another 74 inches of run in front of the ramp and pull the combined approach down to 6.8 degrees. Race Ramps put it plainly: you do not crunch the nose or high center on the rockers.

Each one is 74" long by 16" wide by 4" high, carries 1,500 lbs, weighs 17 lbs, and takes tires up to 14" wide. Each folds in half for transport and storage.

Sold in pairs. See the Portable Pit Stop Ramps and the 16 inch Restyler Ramps these fit. For 56" or 67" ramps you want the other XTenders.

Race Ramps RR-EX-PPS XTenders in front of a Portable Pit Stop ramp

Benefits of the Folding XTenders

6.8 degrees onto a tall ramp
Portable Pit Stop ramps lift 14 inches. Getting a low car up that height on an incline this shallow is the whole reason this part exists, and no shorter approach will do it.
It folds, so it travels
Six feet of ramp that halves to three. This is the version to buy if the set moves between bays or goes on the trailer, and it is what separates this part from the no fold XTender inside the Restyler kits.
Protects the expensive end of the car
A splitter or a front lip is the part that meets the ramp first and costs the most to replace. Nine feet of total run means the nose lifts before the ramp gets near it.
Sixteen inches wide
Takes tires up to 14 inches, matching the Portable Pit Stop and 16 inch Restyler decks so the tire tracks straight through the joint rather than finding an edge.
17 lbs for six feet of ramp
One person sets both, folds both, and stows both. A steel equivalent at this length would need two people and a place to keep it.
Holds where you put it
The traction coating matters most on the piece the tire touches first, because that is where the forward push happens. Foam grips epoxy and sealed concrete without marking. Made in the USA with a one year warranty.
Race Ramps RR-EX-PPS Specifications
Manufacturer Race Ramps
Model RR-EX-PPS, folding version
Type Folding add on incline
Fits Portable Pit Stop Ramps and 16 inch Restyler Ramps, Magna and Classic. Ramps not included
Does Not Fit 20 inch Restyler Ramps. That system takes RR-EX-20
Sold As Pair, two XTenders
Dimensions 74" L x 16" W x 4" H each
Combined Approach Angle 6.8 degrees
Storage Folds in half
Capacity 1,500 lbs each | 3,000 lbs per pair
Maximum Tire Width 14"
Weight 17 lbs each, 34 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

XTender Frequently Asked Questions

I have the 20 inch Restyler. Will these work?

No. These are 16 inches wide, so on a 20 inch deck the tire would cross a four inch step at the joint. The 20 inch system takes RR-EX-20. We can order it for you, so call us on (470) 208-2754 and we will quote it.

How is this different from the XTender in the Restyler Kit?

The fold. Race Ramps ship a no fold XTender inside the Restyler kits, RR-EX-PPS-NF for the 16 inch and RR-EX-20-NF for the 20 inch. This listing is the folding retail version, RR-EX-PPS. Same job, same angle, but this one halves for storage and transport. If the set moves around, buy the folding one.

Do I get ramps with this?

No. This is the pair of folding extenders on their own. They need Portable Pit Stop or 16 inch Restyler ramps in front of them to do anything. If you do not own a set yet, call us and we will quote the system together.

How is this different from the 56 and 67 inch XTenders?

Different ramps, different size. The 56 and 67 inch XTenders are 45 to 48 inches long, 12 or 14 inches wide, and do not fold. These are 74 inches long, 16 inches wide, and fold in half.

How much floor space do I need?

Each XTender adds just over six feet in front of the ramp, so plan on roughly nine to twelve feet of total run depending on which ramps you are pairing them with, plus room to line the car up straight.

Is the fold a weak point?

The rating is 1,500 lbs per XTender, the same as the rest of the Race Ramps line, folded design and all. Set them flat and fully unfolded on level ground, and check the hinge area is seated before the car goes on.

Not sure which ramps you have? Talk to a Pitstop Pro specialist.

Overview

Six Feet of Extra Run, and It Folds in Half

These are add on inclines, not ramps. They fit Portable Pit Stop Ramps and 16 inch Restyler Ramps, Magna and Classic. Running the 20 inch Restyler? That system takes RR-EX-20 instead, which is a call to order. Ramps are not included either way.

Portable Pit Stop and Restyler ramps lift a long way, and lifting a long way over a fixed length means an angle that a splitter finds first. The car stops, or it does not, and you find out the hard way.

These XTenders put another 74 inches of run in front of the ramp and pull the combined approach down to 6.8 degrees. Race Ramps put it plainly: you do not crunch the nose or high center on the rockers.

Each one is 74" long by 16" wide by 4" high, carries 1,500 lbs, weighs 17 lbs, and takes tires up to 14" wide. Each folds in half for transport and storage.

Sold in pairs. See the Portable Pit Stop Ramps and the 16 inch Restyler Ramps these fit. For 56" or 67" ramps you want the other XTenders.

Race Ramps RR-EX-PPS XTenders in front of a Portable Pit Stop ramp

Benefits of the Folding XTenders

6.8 degrees onto a tall ramp Portable Pit Stop ramps lift 14 inches. Getting a low car up that height on an incline this shallow is the whole reason this part exists, and no shorter approach will do it. It folds, so it travels Six feet of ramp that halves to three. This is the version to buy if the set moves between bays or goes on the trailer, and it is what separates this part from the no fold XTender inside the Restyler kits. Protects the expensive end of the car A splitter or a front lip is the part that meets the ramp first and costs the most to replace. Nine feet of total run means the nose lifts before the ramp gets near it. Sixteen inches wide Takes tires up to 14 inches, matching the Portable Pit Stop and 16 inch Restyler decks so the tire tracks straight through the joint rather than finding an edge. 17 lbs for six feet of ramp One person sets both, folds both, and stows both. A steel equivalent at this length would need two people and a place to keep it. Holds where you put it The traction coating matters most on the piece the tire touches first, because that is where the forward push happens. Foam grips epoxy and sealed concrete without marking. Made in the USA with a one year warranty.
Race Ramps RR-EX-PPS Specifications
Manufacturer Race Ramps
Model RR-EX-PPS, folding version
Type Folding add on incline
Fits Portable Pit Stop Ramps and 16 inch Restyler Ramps, Magna and Classic. Ramps not included
Does Not Fit 20 inch Restyler Ramps. That system takes RR-EX-20
Sold As Pair, two XTenders
Dimensions 74" L x 16" W x 4" H each
Combined Approach Angle 6.8 degrees
Storage Folds in half
Capacity 1,500 lbs each | 3,000 lbs per pair
Maximum Tire Width 14"
Weight 17 lbs each, 34 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

XTender Frequently Asked Questions

I have the 20 inch Restyler. Will these work?

No. These are 16 inches wide, so on a 20 inch deck the tire would cross a four inch step at the joint. The 20 inch system takes RR-EX-20. We can order it for you, so call us on (470) 208-2754 and we will quote it.

How is this different from the XTender in the Restyler Kit?

The fold. Race Ramps ship a no fold XTender inside the Restyler kits, RR-EX-PPS-NF for the 16 inch and RR-EX-20-NF for the 20 inch. This listing is the folding retail version, RR-EX-PPS. Same job, same angle, but this one halves for storage and transport. If the set moves around, buy the folding one.

Do I get ramps with this?

No. This is the pair of folding extenders on their own. They need Portable Pit Stop or 16 inch Restyler ramps in front of them to do anything. If you do not own a set yet, call us and we will quote the system together.

How is this different from the 56 and 67 inch XTenders?

Different ramps, different size. The 56 and 67 inch XTenders are 45 to 48 inches long, 12 or 14 inches wide, and do not fold. These are 74 inches long, 16 inches wide, and fold in half.

How much floor space do I need?

Each XTender adds just over six feet in front of the ramp, so plan on roughly nine to twelve feet of total run depending on which ramps you are pairing them with, plus room to line the car up straight.

Is the fold a weak point?

The rating is 1,500 lbs per XTender, the same as the rest of the Race Ramps line, folded design and all. Set them flat and fully unfolded on level ground, and check the hinge area is seated before the car goes on.

Not sure which ramps you have? Talk to a Pitstop Pro specialist.

Call (470) 208-2754 Request a Quote Browse Race Ramps
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews
NO SALES TAX IN MOST STATES

No sales tax on most orders

Give us a call

Our phone team is available 8 AM - 8 PM ET, every day at 470-208-2754

Lifetime Support

Enjoy peace of mind with our support for life. Get in touch!

800+ Reviews

Highly rated and customer-approved. View all!

H
Hunter at Pitstop Pro
Overview

Six Feet of Extra Run, and It Folds in Half

These are add on inclines, not ramps. They fit Portable Pit Stop Ramps and 16 inch Restyler Ramps, Magna and Classic. Running the 20 inch Restyler? That system takes RR-EX-20 instead, which is a call to order. Ramps are not included either way.

Portable Pit Stop and Restyler ramps lift a long way, and lifting a long way over a fixed length means an angle that a splitter finds first. The car stops, or it does not, and you find out the hard way.

These XTenders put another 74 inches of run in front of the ramp and pull the combined approach down to 6.8 degrees. Race Ramps put it plainly: you do not crunch the nose or high center on the rockers.

Each one is 74" long by 16" wide by 4" high, carries 1,500 lbs, weighs 17 lbs, and takes tires up to 14" wide. Each folds in half for transport and storage.

Sold in pairs. See the Portable Pit Stop Ramps and the 16 inch Restyler Ramps these fit. For 56" or 67" ramps you want the other XTenders.

Race Ramps RR-EX-PPS XTenders in front of a Portable Pit Stop ramp

Benefits of the Folding XTenders

6.8 degrees onto a tall ramp Portable Pit Stop ramps lift 14 inches. Getting a low car up that height on an incline this shallow is the whole reason this part exists, and no shorter approach will do it. It folds, so it travels Six feet of ramp that halves to three. This is the version to buy if the set moves between bays or goes on the trailer, and it is what separates this part from the no fold XTender inside the Restyler kits. Protects the expensive end of the car A splitter or a front lip is the part that meets the ramp first and costs the most to replace. Nine feet of total run means the nose lifts before the ramp gets near it. Sixteen inches wide Takes tires up to 14 inches, matching the Portable Pit Stop and 16 inch Restyler decks so the tire tracks straight through the joint rather than finding an edge. 17 lbs for six feet of ramp One person sets both, folds both, and stows both. A steel equivalent at this length would need two people and a place to keep it. Holds where you put it The traction coating matters most on the piece the tire touches first, because that is where the forward push happens. Foam grips epoxy and sealed concrete without marking. Made in the USA with a one year warranty.
Race Ramps RR-EX-PPS Specifications
Manufacturer Race Ramps
Model RR-EX-PPS, folding version
Type Folding add on incline
Fits Portable Pit Stop Ramps and 16 inch Restyler Ramps, Magna and Classic. Ramps not included
Does Not Fit 20 inch Restyler Ramps. That system takes RR-EX-20
Sold As Pair, two XTenders
Dimensions 74" L x 16" W x 4" H each
Combined Approach Angle 6.8 degrees
Storage Folds in half
Capacity 1,500 lbs each | 3,000 lbs per pair
Maximum Tire Width 14"
Weight 17 lbs each, 34 lbs per pair
Material Expanded foam with traction coating
Colour Black
Origin Made in the USA
Warranty 1-year manufacturer warranty | 30-day satisfaction guarantee

XTender Frequently Asked Questions

I have the 20 inch Restyler. Will these work?

No. These are 16 inches wide, so on a 20 inch deck the tire would cross a four inch step at the joint. The 20 inch system takes RR-EX-20. We can order it for you, so call us on (470) 208-2754 and we will quote it.

How is this different from the XTender in the Restyler Kit?

The fold. Race Ramps ship a no fold XTender inside the Restyler kits, RR-EX-PPS-NF for the 16 inch and RR-EX-20-NF for the 20 inch. This listing is the folding retail version, RR-EX-PPS. Same job, same angle, but this one halves for storage and transport. If the set moves around, buy the folding one.

Do I get ramps with this?

No. This is the pair of folding extenders on their own. They need Portable Pit Stop or 16 inch Restyler ramps in front of them to do anything. If you do not own a set yet, call us and we will quote the system together.

How is this different from the 56 and 67 inch XTenders?

Different ramps, different size. The 56 and 67 inch XTenders are 45 to 48 inches long, 12 or 14 inches wide, and do not fold. These are 74 inches long, 16 inches wide, and fold in half.

How much floor space do I need?

Each XTender adds just over six feet in front of the ramp, so plan on roughly nine to twelve feet of total run depending on which ramps you are pairing them with, plus room to line the car up straight.

Is the fold a weak point?

The rating is 1,500 lbs per XTender, the same as the rest of the Race Ramps line, folded design and all. Set them flat and fully unfolded on level ground, and check the hinge area is seated before the car goes on.

Not sure which ramps you have? Talk to a Pitstop Pro specialist.

Call (470) 208-2754 Request a Quote Browse Race Ramps
Shipping/Returns

Shipping & Returns

  • Shipping Policy
    • Orders are typically processed and shipped within 48 hours after payment is received. Orders placed before 10:00 AM CST may ship the same day.
    • Estimated delivery time is 1–5 business days for most locations, depending on product availability and destination.
    • Processing and delivery times for ground and expedited shipments are estimates and are not guaranteed.
    • Shipping costs are calculated during checkout based on the delivery address and selected shipping method.
    • Products requiring freight delivery may be subject to separately calculated shipping charges.
  • Domestic Shipping
    • Race Ramps products are shipped throughout the United States using FedEx and LTL freight carriers.
    • Unless another shipping option is selected during checkout, orders are shipped through FedEx Ground or FedEx Home Delivery.
    • Estimated ground delivery time is 1–5 business days for most locations.
  • International Shipping
    • Some Race Ramps products may not be eligible for international shipping.
    • International customers should contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com before placing an order.
    • International orders may require manual verification, and final shipping charges may differ from the initial order confirmation due to international shipping rates, tariffs, duties, and taxes.
  • Returns Policy (30 Days)
    • Undamaged products may be returned within 30 days for a product-only refund or exchange.
    • Refunds are issued using the original payment method.
    • Original shipping and handling charges are nonrefundable.
    • Exchanges for products of the same dollar value will not incur additional shipping or handling charges.
    • All LTP and custom-item sales are final and are not eligible for return.
  • How to Initiate a Return
    • Before returning a product, contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com to request a Return Goods Authorization (RGA) number.
    • Returns must be shipped using a prepaid, insured, and trackable shipping method.
    • Products returned without an approved RGA number will not be processed.
    • Approved returns should be sent to:

      Race Ramps LLC
      ATTN: Returns
      N102W19400 Willow Creek Way
      Germantown, WI 53022

Shipping, return, and delivery policies are subject to change without prior notice.

Warranty

Warranty

  • Warranty Period:
    • Race Ramps purchased from an authorized dealer or directly from Race Ramps LLC are covered by a one-year limited warranty.
    • The warranty begins on the original purchase date and applies only to the original owner.
    • Warranty coverage is not transferable.
  • Warranty Coverage:
    • Coverage is limited to the repair or replacement of manufacturer defects.
    • Race Ramps LLC will determine whether an eligible product should be repaired or replaced.
    • Products sold by Race Ramps but manufactured by another company are covered by that manufacturer’s warranty and policies.
  • What the Warranty Does Not Cover:
    • Damage caused by improper, unintended, or unsafe use.
    • Damage to a vehicle, personal injury, labor charges, or other related damages or expenses.
    • Consequential, incidental, or indirect damages or costs.
    • Normal surface impressions, wear, staining, or cosmetic changes resulting from regular use.
    • Damage caused by exceeding the product’s stated weight capacity, temperature limits, or intended application.
  • Proper Use Requirements:
    • Race Ramps are designed for vehicles with high-performance, high-speed-rated tires.
    • Do not use Race Ramps with heavy-lug mud tires or excessively narrow tires unless the product is specifically designed for that application.
    • Standard Race Ramps are designed to support up to 1,500 pounds per tire, per ramp, unless a different capacity is listed for the specific model.
    • Ramps must be used on a flat, solid, and level surface.
    • Do not use Race Ramps to bridge gaps or combine them with wood, metal, or other unsupported materials.
    • The surface temperature of the ramps must remain below 150°F (65.56°C).
  • Normal Surface Impressions:
    • Vehicle tire weight may leave a slight impression of up to approximately 1/8 inch in the ramp’s surface.
    • This is considered normal and does not necessarily indicate a product defect.
  • Ground Surface and Safety:
    • Sweep cement, asphalt, or other surfaces before placing the ramps.
    • Rocks, gravel, and debris underneath the ramps may cause sliding, denting, or surface damage.
  • Temperature and Storage:
    • Race Ramps may be used indoors or outdoors as long as their surface temperature remains below 150°F (65.56°C).
    • Avoid leaving the ramps in prolonged direct sunlight.
    • In warmer climates, do not store the ramps outdoors or inside a vehicle trunk where temperatures may become excessive.
  • Cleaning and Automotive Fluids:
    • Clean Race Ramps using a scrub brush with soap and water.
    • For cleaning while traveling, WD-40 may be applied and wiped away with a clean cloth.
    • Race Ramps resist most automotive fluids, but some fluids may stain or penetrate the surface if they are not removed promptly.
  • Warranty Assistance:
    • Contact Pit Stop Pro before returning or disposing of a product believed to have a warranty defect.
    • Photos, proof of purchase, product information, and a description of the issue may be required to evaluate a warranty claim.
  • Important Notes:
    • Product specifications may change without prior notice due to ongoing research and product development.
    • Always follow the instructions and weight limitations provided for your specific Race Ramps model.

Need help with a Race Ramps warranty claim? Contact Pit Stop Pro at (470) 208-2754 or support@pitstop-pro.com.

★Reviews